mic6315 open - drain p reset circuit general description the mic6315 is an inexpensive reset generator circuit that monitors power supplies in microprocessor - based systems. the function of this device is to assert a reset if either the power supply drops below a designated reset threshold level or /mr is forced low. several different reset threshold levels are available to accommodate 3v, 3.3v, or 5v powered systems. the mic6315 has an active low, open - drain /reset output. the reset output is guaranteed to remain asserted for a minimum of either 20ms, 140ms, or 1100ms after v cc has risen above the designed reset threshold level. the mic6315 is available in a 4 - pin sot -1 43 package. datasheets and support documentation are available on micrels web site at : www.micrel.com . features ? precision voltage monitor for 3v, 3.3v , or 5v power supplies ? /reset remains valid with v cc as low as 1v ? 5a supply current ? 20ms, 140ms , or 1100ms minimum reset pulse width s available ? manual reset input ? available in 4- pin sot - 143 package applications ? portable equipment ? intelligent instruments ? critical microprocessor power monitoring ? printers/computers ? embe dded controllers typical application micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 (408) 944 - 0800 ? fax + 1 (408) 474 - 1000 ? http://www.micrel.com october 17, 2014 revi sion 2.0 downloaded from: http:///
micrel, inc. mic6315 ordering information part number ( 1 , 2 ) marking (3) nominal v th (v) minimum t rst (ms) operating temperature range package lead finish mic6315 - 26d2uy ny 2.63 20 C 40 c to +85 c 4-pin sot - 143 pb-free mic6315 - 29d2uy nm 2.93 20 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 30d2uy n2 3.00 20 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 31d2uy nf 3.08 20 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 40d2uy nw 4.00 20 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 41d2uy n6 4.10 20 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 44d2uy ng 4.38 20 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 46d2uy nq 4.63 20 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 26d3uy nr 2.63 140 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 29d3uy np 2.93 140 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 30d3uy n3 3.00 140 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 31d3uy nu 3.08 140 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 40d3uy n8 4.00 140 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 41d3uy n5 4.10 140 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 42d3uy 05 4.20 140 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 44d3uy nh 4.38 140 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 46d3uy nx 4.63 140 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 -2 6d 4 uy ns 2.63 1100 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 29d4uy nn 2.93 1100 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 30d4uy n4 3.00 1100 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 31d4uy 2n 3.08 1100 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 40d4uy m9 4.00 1100 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 41d4uy m7 4.10 1100 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 44d4uy nj 4.38 1100 C 40 c to +85 c 4- pin sot - 143 pb-free mic6315 - 46d4uy nz 4.63 1100 C 40 c to +85 c 4- pin sot - 143 pb-free note: 1. ship format tape and reel only (ordering part number add space tr example. mic6315 - 26d2uy tr) . 2. standa rd reel quantity is 3000 pieces . reel diameter 7 in. / hub diameter 2 in. / width 8 mm . 3. underbar symbol ( _ ) may not be to scale. october 17, 2014 2 revision 2.0 downloaded from: http:///
micrel, inc. mic6315 pin configuration 4- pin sot - 143 ( u) (top view) pin description pin number pin name pin function 1 gnd ic ground . 2 /reset /reset goes low if v cc falls below the reset threshold and remains asserted for one reset timeout period after v cc exceeds the reset threshold. 3 /mr manual reset input: a logic low on /mr forces a reset. the reset will remain asserted as long as /mr is held low and for one reset timeout period after /mr goes high. this input can be shorted to ground via a switch or be driven by ttl or cmos logic. float if unused. 4 vcc power supply input. october 17, 2014 3 revision 2.0 downloaded from: http:///
micrel, inc. mic6315 absolute maximum ratings ( 4 ) terminal voltage ( vcc, /reset ). ..................................... ? 0.3v to +6.0v ( /mr ) ............................................ ? 0.3v to (v cc + 0.3v) rate - of - rise (v cc ) ................................................. 100v/ s input current (vcc, /mr) ............................................ 20ma output current (/reset) ............................................ 20ma lead temperature (soldering, 10s) ............................ 300 c storage temperature (t s ) ......................... ? 65c to +150 c esd rating ( 6 ) .................................................................. 3 kv operating ratings ( 5 ) input voltage ( /reset ) .................................... gnd to 5.5v operating temperature range ................... C 40c to +85c junction temperature (t j ) ........................ C 40c to +125c power dissipation (t a = +70 c) ............................... 320mw electrical characteristics for typical values, v cc = 2.5v to 5.5v ; t a = + 25c, bold values indicate C 40c t a +85c, unless noted. symbol parameter condition min . typ . max . units v cc operating voltage range 1 5.5 v i cc supply current v cc = 5.5v, no load. 5 15 a v cc = 3.6v, no load. 5 10 v th reset voltage threshold note 7 v th ? 2.5% v th v th + 2.5% v t rst reset timeout period d2u 20 28 44 ms d3u 140 200 320 d4u 1100 1500 2500 v ol /reset output voltage v cc 4.0v, t sink = 3.2ma 0.4 v v cc 2.5v, t sink = 1.2ma 0.3 v cc 1.0v, t sink = 50 a 0.3 /reset output leakage /reset de - asserted 1 a /mr minimum pulse width 10 s /mr - to - reset delay 0.5 s v ih /mr input threshold v th > 4.0v 2.3 v v th < 4.0v 0.7 v cc v il /mr input threshold v th > 4.0v 0.8 v v th < 4.0v 0.25 v cc /mr pull - up resistance 10 20 30 k ? /mr glitch immunity 100 ns notes: 4. exceeding the absolute maximum ratings may damage the device. 5. the device is not guaranteed to function outside its operating ratings. 6. devices are esd sensitive. handling precautions are recommended. human body model, 1.5k ? in series with 100pf. 7. various reset thresholds available. see ordering information or contact factory. october 17, 2014 4 revision 2.0 downloaded from: http:///
micrel, inc. mic6315 timing diagram functional diagram october 17, 2014 5 revision 2.0 downloaded from: http:///
micrel, inc. mic6315 application information microprocessor reset the /reset pin is asserted whenever v cc falls below the reset threshold voltage or if /mr (manual reset) is forced low. the /reset pin remains asserted for the duration of the reset timeout period after v cc has risen above the reset threshold or /mr has returned high. the reset function ensures the microprocessor is properly reset and powers up in a known condition after a power failure. /reset will remain valid with v cc as low as 1v. the /reset output is a simple open - drain n - channel mosfet structure. a pull - up resistor must be used to pull this output up to some voltage. for most applications, this voltage will be the same power supply that supplies v cc to the mic6315. it is possible, however, to tie this r esistor to some other voltage. this will allow the mic6315 to monitor one voltage while level - shifting the /reset output to some other voltage. the pull - up voltage must be limited to 6.0v or less (absolute maximum) to avoid damage to the mic6315. the resis tor must be small enough to supply current to the inputs and leakage paths that are driven by the /reset output. /reset valid at low voltage as v cc drops to 0v, the mic6315 will no longer be able to pull the /reset output low. at this point, the pull - up re sistor will pull the output high. the value of the pull - up resistor and the voltage it is connected to will affect the point at which this happens. wire oring the /reset output because the reset output is open - drain, several reset sources can be wire - or e d, in parallel, to allow resets from multiple sources. v cc transients the mic6315 is relatively immune to negative - going v cc glitches below the reset threshold. typically, a negative - going transient 125mv below the reset threshold with duration of 20 s o r less will not cause an unwanted reset. if additional transient immunity is needed, a bypass capacitor can be placed a close as possible to the mic6315. figure 1 . mic6315 as used in a multiple supply system october 17, 2014 6 revision 2.0 downloaded from: http:///
micrel, inc. mic6315 package information and recommended landing pattern ( 8 ) 4-pin sot - 143 (u) note: 8. package information is correct as of the publication date. for updates and most current information, go to www.micrel.com . october 17, 2014 7 revision 2.0 downloaded from: http:///
micrel, inc. mic6315 micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944 - 0800 fax +1 (408) 474 - 1000 web http://www.micrel.com micrel, inc. is a leading global manufacturer of ic solutions for the worldwide high performance l inear and power, lan, and t iming & communications markets. the companys products include advanced mixed - signal, analog & power semiconductors; high - performance communication, clock management, mems - based clock oscillators & crystal - less clock generators, ethernet switches, and physical layer transceiver ics. company customers include leading manufact urers of enterprise, consumer, industrial, mobile, telecommunications, automo tive, and computer products. corporation headquarters and state - of - the - art wafer fabrication facilities are located in san jose, ca, with regional sales and support offices and advanced technology design centers situated throughout the americas, europe, and asia. additionally, the company maintains an extensive network of distributors and reps worldwide. micrel makes no representations or warranties with respect to the accuracy or completeness of the inf ormation furnished in this data sheet. this information is not intended as a warranty and micrel does not assume responsibility for its use. micrel reserves the right to change circuitry, specifications and descriptions at any ti me without notice. no license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. except as provided in micrels terms and conditions of sale for such products , micrel assumes no li ability whatsoever, and micrel disclaims any express or implied warranty relating to the sale and/or use of mi crel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copy right , or other intellectual property right. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. life support devices or systems are devices or sy stems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. a purchasers u se or sale of micrel products for use in life support appliances, devices or systems is a purchasers own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 20 05 micrel, incorporated. october 17, 2014 8 revision 2.0 downloaded from: http:///
|
